O-Series: Offset Downspout Boot
 

 

Related Products

 
 
Offset Overview

The J.R. Hoe O-Series downspout boot features a 2 inch offset at the bottom of the boot allowing for a vertical connection to the underground drainage pipe. The offset transition is designed to provide enough clearance from the building wall to fit a pipe hub around the downspout boot. A ¾” fastening lug slot allows for easy installation to the building wall. The O-Series downspout boots feature a distinctive contoured design that is engineered for superior hydraulic conveyance, aesthetic appeal and durability.

Downloads

      

   

Product Info
  • Available in hundreds of different sizes - view our Size Chart
  • Custom or non-standard downspout boots can be designed to meet special requirements or specifications
  • Various coating options options are available including primer coat and powder coat in a wide range of colors
  • Qualified for LEED Credits 4.1/4.2 Recycled Content and LEED Credits 5.1/5.2 Regional Materials
  • For additional information or questions please contact us
 

Drawing Selector

Please choose from the drop down menus provided below to select the correct product drawing or select get a quote.

{{field.label}}

Quantity

{{ProductNumber}}

{{options.coating}} mounting {{options.pipe_size}}" {{options.pipe_material}} coupling

Your Product

Product Preview

Additional drawings available upon request.

 

 

Frequently Asked Questions

What is the purpose of the 2 inch offset on the O-Series boot?
The 2 inch offset at the bottom of the boot moves the outlet away from the building wall so a vertical connection can be made to the underground drainage pipe. The offset provides the clearance needed to fit a pipe hub or coupling around the boot spigot without interference from the foundation or wall face.

 

When should I specify an Offset boot instead of an Angular or Ninety boot?
Specify the O-Series when the receiving storm pipe rises vertically directly below the downspout, close to the building. If the pipe is farther from the wall or the connection is at 45 degrees, use the A-Series. If the receiving pipe runs horizontally at or near grade, use the N-Series with its 90 degree outlet.

 

How does the O-Series boot attach to the building wall?
Each boot includes a 3/4 inch fastening lug slot for anchoring to the wall. J.R. Hoe offers stainless steel hex bolt and expansion shield mounting hardware for concrete, masonry, or brick, plus theft-resistant penta-head bolt options and neoprene wall spacers when the boot must stand off the wall to align with the piping.

 

Is a cleanout available on the Offset boot?
Yes. Many O-Series models are offered with an integral cleanout plug, indicated by a C in the model number, such as O-4528C. The on-body cleanout provides rodding access for drainage system maintenance and can eliminate the need for a separate in-ground cleanout downstream.

 

What material is the O-Series boot cast from and what specification should I reference?
O-Series boots are cast from gray iron conforming to ASTM A48 Class 30B, a grade known for compressive strength, hardness, and wear resistance. A downloadable general specification for the O-Series is available on the product page for editing into the project manual.

 

How do I coordinate the vertical pipe stub-up with the O-Series boot?
The underground riser should be located to align with the boot outlet, accounting for the 2 inch offset from the wall face. It is often simplest to install or verify the storm stub-up before setting the boot, then make the joint with a Fernco style flexible coupling or a hub connection over the spigot. Neoprene wall spacers can shift the boot out from the wall if field conditions require additional alignment.

 

What top bell sizes are available for the O-Series?
The O-Series is offered in hundreds of size combinations to fit standard commercial downspouts, including common 3 x 4 and 4 x 5 profiles as well as larger and round sections, with lengths from 16 to 80 inches. The published size chart lists inside bell dimensions, lengths, and spigot outside diameters for each model.

 

Can the O-Series boot be powder coated to match the building?
Yes. O-Series boots are available bare, primer coated for field painting, or factory powder coated in a wide range of colors, close to 200 options. The powder coating uses a proprietary two coat system validated by in-house quality assessment and third party salt spray testing.

 

Does the O-Series contribute to LEED goals?
Yes. Like all J.R. Hoe cast iron boots, the O-Series is qualified for LEED Recycled Content credits and Regional Materials credits because it is cast in the USA from recycled iron. LEED documentation support is available from the factory.

 

How do I find the correct O-Series drawing for my submittal?
Use the DWG Selector on the website, choose the O-Series and your bell size, length, coating, mounting, and coupling options, and the tool generates the correct numbered product drawing as a PDF. Additional drawing formats are available from the factory upon request.